LG Display LB104S01-TL05 10.4-inch SVGA TFT-LCD Panel Specifications
LB104S01-TL05 LG Display 10.4-inch SVGA TFT-LCD Panel Specs
Introduction & Core Highlights
The LB104S01-TL05 by LG Display is an industrial-grade 10.4-inch transmissive active-matrix liquid crystal display module. Operating on an amorphous silicon TFT platform, this panel utilizes a parallel TTL interface to support legacy systems. It provides standard resolution and brightness for reliable indoor visualization terminals.
- Core Specs: 10.4″ Diagonal | 800 × 600 SVGA | 400 cd/m² Brightness | 6-bit Parallel TTL
- Key Benefits: Direct legacy drop-in replacement; simplified graphics logic integration.
- Integration Note: Parallel TTL signals are sensitive to bus length. Keeping trace lengths equal prevents signal skew across the 31-pin connector.
Request Datasheet PDF for LB104S01-TL05
Technical Analysis of Interface and Optical Architecture
The parallel TTL (Transistor-Transistor Logic) interface remains a reliable choice for legacy industrial microcontrollers. The LB104S01-TL05 uses a single-channel 6-bit TTL bus configuration, which directly presents 262,144 colors without the protocol translation delay associated with LVDS serializer chips. Understanding LCD core technology is helpful here, as matching setup and hold times on the parallel data lines avoids clock synchronization errors.
Operating in a Normally White TN (Twisted Nematic) display mode, the module provides a typical contrast ratio of 500:1. The viewing angles are constrained to 65/65 degrees horizontally and 50/60 degrees vertically. You can compare these viewing limits to looking through a narrow optical window; shifting too far off-axis causes contrast degradation and eventual grayscale inversion. System designers must locate the panel at optimal viewing heights relative to operators.
The optical system features a dual-CCFL (Cold Cathode Fluorescent Lamp) backlight assembly. Delivering a uniform 400 nits of surface luminance, it ensures readability in standard control rooms. Because CCFL backlights require high-voltage AC start and drive signals, inverter board selection and thermal isolation are important system integration factors. Managing the heat dissipated by the lamps helps maintain stable performance.
Optimized Application Scenarios
- Legacy Factory Automation HMIs: Drop-in replacement for older industrial terminals. Refer to smart factory HMI display specifications for compatibility rules.
- CNC Machining Control Panels: The 800×600 resolution maps directly to older text-based toolpath visualization displays.
- Medical Diagnostic Monitors: Suitable for legacy clinical equipment requiring a 4:3 aspect ratio display.
- Marine Wheelhouse Displays: The 400-nit panel provides adequate visibility under sheltered marine lighting. Consult the guide on vibration resistance for industrial displays to review mechanical mounting strategies.
Best Match: Ideal for legacy parallel TTL industrial controller retrofits requiring a native 10.4-inch SVGA display panel.
Key Specification Parameters
| Parameter Group | Specification | Typical Value |
|---|---|---|
| Mechanical & Screen | Diagonal Size | 10.4 inches (26.4 cm) |
| Resolution | 800 (RGB) × 600 (SVGA) | |
| Aspect Ratio | 4:3 (Landscape) | |
| Optical & Electro | Luminance | 400 cd/m² (Typical) |
| Contrast Ratio | 500:1 (Typical) | |
| Viewing Angle (L/R/U/D) | 65° / 65° / 50° / 60° (Typical) | |
| Electrical & Environmental | Signal Interface | TTL Parallel (1-ch, 6-bit), 31 pins |
| Supply Voltage (VDD) | 3.3V (Typical) | |
| Operating Temperature | 0°C to +50°C |
Engineer FAQ
How do I drive the LB104S01-TL05 from a modern board with only LVDS outputs?
A TTL-to-LVDS converter board is required. The board receives the LVDS serialization stream, decodes it, and splits the data into the 6-bit parallel RGB signals required by the panel’s 31-pin connector.
What is the primary factor limiting the lifespan of this display?
The CCFL backlight lamps degrade faster than the LCD cell. Running the backlight at the minimum required brightness level reduces operating temperature and lamp wear. Review industrial LCD backlight lifespan management for maintenance details.
Are there specific considerations for mechanical mounting?
Avoid applying uneven pressure to the outer display bezel. Twisting the chassis can distort the liquid crystal cell gap, causing localized display anomalies like light leakage or mura patterns.
Closing Statement
By offering direct compatibility with legacy parallel interfaces, the LB104S01-TL05 display panel allows engineers to maintain existing industrial systems. The SVGA resolution and standard brightness ensure a direct replacement path, avoiding the costs of redesigning the control architecture.